A block’s zone sets what the land can be used for, which uses need approval and which are ruled out.
The zone is not the only control. Height limits, lot sizes, density codes and overlays for hazards such as flooding or bushfire can also apply.
Each state runs its own system. This guide covers New South Wales (NSW), Victoria, Queensland, Western Australia (WA) and South Australia (SA). It ends with how to check the zone on a property.
What a zone does
Zones identify the types of development that can happen in an area. The planning scheme then sets when approval is needed in each zone, plus standards such as building height.
In NSW, each zone’s land use table has four parts: the zone’s objectives, uses permitted without consent, uses permitted with consent, and prohibited uses.
A use that is permitted with consent still needs development consent. Permissible does not mean approved.
New South Wales: five residential zones
In NSW, local environmental plans (LEPs) made under a state template called the Standard Instrument use five residential zones:
- R1 General Residential: a variety of housing types and densities.
- R2 Low Density Residential: housing in a low density residential environment.
- R3 Medium Density Residential: a variety of housing types in a medium density environment.
- R4 High Density Residential: a variety of housing types in a high density environment.
- R5 Large Lot Residential: residential housing in a rural setting.
The Standard Instrument also includes optional clauses for minimum subdivision lot size, height of buildings and floor space ratio. Councils can adopt these in their own LEPs.
How NSW widened what R2 land allows
State policy can change what a zone allows without the land being rezoned. The NSW Government’s Low and Mid-Rise Housing Policy is one example.
Its first stage started on 1 July 2024, according to the NSW Government’s planning website. It made dual occupancies and semi-detached homes permitted with consent in R2 zones across NSW.
A second stage started on 28 February 2025. It covers residential land within 800 metres’ walk of nominated town centres and train, metro or light rail stations.
Those areas are in Greater Sydney, the Central Coast, the Lower Hunter and Newcastle, and Illawarra-Shoalhaven. There, the policy allows a wider mix of terraces, townhouses, apartments and shop-top housing.
It also sets standards. If an application meets them, a council cannot refuse it for failing those standards. Sites affected by certain hazards, such as bushfire-prone land and some flood-prone land, are excluded.
Victoria: height and garden limits set by the zone
Victoria’s residential zones are described in the state’s Planning Practice Note 91, dated January 2026:
- Neighbourhood Residential Zone (NRZ): areas with no expected change to mostly single- and double-storey character.
- General Residential Zone (GRZ): areas where three-storey housing exists or is planned.
- Residential Growth Zone (RGZ): higher density near services, jobs and public transport.
- Housing Choice and Transport Zone (HCTZ): well-serviced areas near activity centres, with high-density and mid-rise housing.
- Mixed Use Zone (MUZ): areas suited to a mix of residential and other uses.
- Township Zone (TZ): small towns without a separate residential, commercial and industrial structure.
- Low Density Residential Zone (LDRZ): fringe areas with large lots.
Height controls differ by zone. For a dwelling or residential building in the NRZ, GRZ and RGZ, they work like this:
In the NRZ, the maximum is 9 metres and two storeys, excluding a basement. It is mandatory. A council schedule can lift the height but must keep the two-storey limit.
In the GRZ, the mandatory maximum is 11 metres and three storeys, excluding a basement.
In the RGZ, the maximum is 13.5 metres. It is discretionary unless a schedule sets a height, which then becomes mandatory.
The NRZ and GRZ also require a minimum garden area on lots of 400 square metres or more. The share rises with lot size.
The requirement cannot be waived in the NRZ. It can be waived in the GRZ where there is strategic justification.
Queensland: each council writes its own scheme
In Queensland, each council prepares its own planning scheme under the Planning Act 2016, according to the state planning department. The state approves the scheme and sets the parts it must include.
Councils must choose their zones from a standard state list, but each council writes its own rules for them. A council’s scheme sets out when approval is needed in each zone, plus standards such as building height, parking and landscaping.
Queensland schemes also sort development into categories:
- Accepted development: needs no development approval if it meets the set requirements.
- Code assessment: the proposal needs approval and is checked against set benchmarks.
- Impact assessment: the proposal needs approval and is assessed more broadly, against the whole planning scheme.
Western Australia: the zone plus an R-Code
In WA, a property’s zone in the local planning scheme can come with a density code from the Residential Design Codes, known as the R-Codes.
A property shown as “Residential R30”, for example, is in the Residential zone with a density code of R30.
The R-Codes set minimum and average lot areas, or plot ratios, for each density code. Volume 1 covers all single houses and grouped dwellings, plus apartments at R60 and below. Volume 2 covers apartments at R80 and above.
Local governments administer the R-Codes, so questions about a specific site go to the local council.
South Australia: one code for the whole state
South Australia uses a single Planning and Design Code across the state. Zones are its main layer, according to PlanSA.
Residential land sits in neighbourhood zones, including the General Neighbourhood, Suburban Neighbourhood, Established Neighbourhood and Housing Diversity Neighbourhood zones.
Subzones refine a zone for part of its area. Technical and numeric variations allow local settings, such as site areas or building heights, without a new zone.
Overlays can override the zone
Overlays sit on top of zones and flag a site’s particular features. Examples include flood, bushfire, landslide and heritage overlays.
An overlay can add requirements or limit what the zone would otherwise allow. In South Australia, overlay policies take precedence over other Code policies, according to PlanSA.
Two blocks in the same zone can face different rules because one carries an overlay.
How to check the zone on a property
- NSW: the NSW Planning Portal Spatial Viewer shows map layers such as land zoning and height of buildings. Councils issue Section 10.7 planning certificates, formerly Section 149 certificates, covering zoning, planning controls and constraints such as contamination, flooding and bushfire-prone land.
- Victoria: VicPlan shows the zone and overlay details for a site and can generate a planning report. A VicPlan Planning Property Report states it is not a planning certificate issued under Section 199 of the Planning and Environment Act 1987.
- Queensland: check the council’s planning scheme, including its zone and overlay maps.
- WA: check the council’s local planning scheme map, which shows the zone and R-Code. Some councils, such as the City of Vincent, offer this through online maps.
- SA: the South Australian Property and Planning Atlas (SAPPA) displays current zoning across the state.
What this means for you
The zone shows what a site could allow, not what will be approved. A proposal still has to meet the other controls that apply, and may need council approval.
What a zone allows can also change at state level, as the NSW low and mid-rise reforms show.
For a knockdown, a second dwelling or a subdivision, the zone, any overlays and the local controls together set the limits. In NSW and Victoria, a planning certificate gives the formal record.
This article is general information, not legal or planning advice. Confirm the rules for a specific property with the local council.
Sources
NSW Standard Instrument LEP, NSW Low and Mid-Rise Housing Policy, NSW Low and Mid-Rise Housing Policy key provisions, NSW Planning Portal planning certificates, NSW Spatial Viewer guide, Planning Practice Note 91 (Vic), VicPlan, VicPlan Planning Property Report (example), Queensland planning system overview, Planning Regulation 2017 (Qld), Brisbane City Council, Moreton Bay City Council, Townsville City Council, WA Residential Design Codes, City of Vincent, City of Cockburn, PlanSA Planning and Design Code guide, SA Property and Planning Atlas